Installation of high-voltage boat motors at fair prices
Status:
available
On request
Your mobile installation service for installing a new high-voltage electric motor in your boat. More power and performance than conventional 48V systems. Optionally, we also have partners in your area or work with your local shipyard or boat builder.
We install motors from ePropulsion, Elco, Mitek, Aquamot, and other manufacturers.
Do you have any questions? Feel free to contact us for an individual offer!
Properties Installation of high-voltage boat motors
special feature
High voltage
Location
mobile
Our mobile installation service
We are receiving more and more requests for the installation of high-voltage boat motors (ePropulsion, Elco, Mitek, Aquamot, ...) in our customers' boats. We offer a mobile high-voltage installation service.
Is your boat stored in a hall with a power connection or on the shipyard premises during winter? That's all we need!
If you want us to remove the old diesel engine, it would be helpful if there is a small crane available on site. In theory, installation can also be done outdoors in dry weather.
Our Björn drives directly to your boat with his workshop van and carries out the conversion.
Conversion of a motorboat to high-voltage drive
Frequently Asked Questions about High-Voltage Conversion
It depends! If the old motor has already been removed, installing a new drive takes about 2-3 days.
For a high-voltage motor, special components need to be installed, so the electrical connection takes a few hours longer than with a low-voltage installation.
Note: Due to special circumstances or extra requests, the installation may always take a little longer.
It depends! In Germany, the hourly rates of shipyards and boat builders are usually between 60 and 100€ per hour (this may vary abroad).
Assuming 2 days at 80€ per hour and 8 working hours per day, we have installation costs starting from 1,600€ net for the installation. In addition, there is usually a flat rate for materials (depending on the installation situation) and the costs for travel and accommodation.
You can save the most money by using a boat builder or service that has already installed a high-voltage motor before. An inexperienced boat builder may need 3 or 4 days for the installation. Even if the boat builder charges €10 or €20 less per hour, it will end up being significantly more expensive for you overall.
Certain tasks, such as removing the old diesel engine or cleaning the engine compartment, can also be carried out by yourself in consultation with us or the shipyard.
To install a high-voltage electric motor, certified specialist personnel with a special certificate are required. Installation must not be carried out by persons without certification, as there is a risk to life!
In addition, users of the boats must be trained accordingly in the use of the high-voltage system and informed about safety risks.
Offer for high-voltage boat motors
It’s best if you send us some information about the boat and a few pictures of the hull and installation space, then we will prepare an individual offer for you.
Process of high-voltage installation
The actual installation depends on the type of engine. An outboard motor can be attached to the boat relatively easily. Installing an inboard or pod motor generally takes an extra day.
A lot of time is needed for the meticulous electrical connection, as there are many things to consider and special components are used for the installation.
Afterwards, the system must be thoroughly tested and documented. Instruction for the boat operators by our certified boat builder is also an integral part of the installation.
Local boat builders near you
-
Installation of high-voltage boat motor in Berlin (Wannsee, Müggelsee, Müritz)
-
Installation of high-voltage boat motor Baltic Sea (Greifswald, Kiel, Wismar, Rügen, Rostock)
-
Installation of high-voltage boat motor North Sea (Bremen, Bremerhaven, Elbe)
-
Installation of high-voltage boat motor Hamburg
-
Installation of high-voltage boat motor Bavaria (Lake Starnberg, Lake Chiem)
-
Installation of high-voltage boat motor Lake Constance (Germany, Switzerland)
Boat builders near you (Europe)
-
Installation of high-voltage boat motor France
-
Installation of high-voltage boat motor Spain
-
Installation of high-voltage boat motor Italy
-
Installation of high-voltage boat motor Netherlands
-
Installation of high-voltage boat motor Poland
Advantages of a high-voltage boat motor
-
Higher efficiency than low voltage
-
Higher performance possible
-
Smaller cable cross-sections
-
Especially for planing boats, there are hardly any alternatives to a high-voltage drive.
-
High voltage is always identified by the orange cables and adapters that come from the motor and battery.
Safety with high-voltage boat motors (what should be considered?)
-
shielded high-voltage cables with insulation monitoring
-
Interlock connectors on all components
-
Equipotential bonding in the boat
-
Special high-voltage components (main switch, fuses, contactor box)
-
Special safety equipment: voltage tester, clothing, rubber gloves
Shipyard or boat builder for high-voltage conversion
Installing an electric boat motor is a big step towards a whole new boating experience. With our mobile installation service, we offer you a convenient, flexible, and professional solution.
If you are ready to make the switch to electric propulsion, get in touch with us.
Consultation on high-voltage motors with more power
Open questions?
How does the order process work?
Simply click on "Add to cart". In the next step, enter your personal data and choose your preferred payment method.
As a specialist dealer, we will check your order and send you an order confirmation and invoice. After receipt of payment, we will send the desired items directly to the desired delivery address.
Within Germany, the delivery time is 3-4 working days. Of course, you will also receive a tracking link for your order.
Afterwards, we are always available personally for questions about assembly. Of course, we also provide instructions, tips and soon also explanatory videos.
For all products in our range, we offer a 2-year warranty - for some products even more.
In case of complaints, we are your contact person, we help you to ensure that everything runs smoothly. You can always reach us by email or phone. We also provide support for possible spare parts at any time. Your boat is our drive.
Your advantages using greenboatsolutions
Few clicks will save you a lot of time and stress!
You will get a result within 5 minutes.
You compare nearly 600 different electric motors.
You have an overview of more than 30 manufacturers.